How To Break In A New Air Compressor (6 Easy Steps)
An air compressor is a handy tool to have around the house as they’re great for inflating tires, as well as for powering air tools. But before you can start using your air compressor, you need to “break it in” first, and breaking in a new air compressor is a simple process, but there are some things you need to do to make sure it's done properly. So in this article, I will tell you how to break in an air compressor so without any further ado let's take a look at this guide.
Why Do You Need To Break In An Air Compressor?
An air compressor is a machine that uses a gas engine or electric motor to power a device that sucks in air and compresses it into a smaller volume. Air compressors can be used to power many different types of tools, including impact wrenches, ratchets, drills, and paint sprayers. In order to get the most out of your air compressor, it is important to break it in properly and there are several reasons why you need to break in an air compressor.
First, it will help extend the life of your compressor, and second, it will improve the performance of the compressor. Third, it will help you avoid problems down the road. Breaking in your air compressor is not difficult and below I have listed some steps that you can follow to do it.
What Happens If You Don't Break In An Air Compressor?
If you don't break in an air compressor, the piston rings will not seat properly and the oil will not be able to lubricate all of the moving parts. This can lead to premature wear and tear on the compressor, and it may even cause the compressor to develop other issues over the years.
Steps For Breaking In A New Air Compressor:
An air compressor is a nice handy tool to have around as whether you are inflating a tire or powering up a nail gun, an air compressor can be a lifesaver. But before you can use your new air compressor, you need to break it in and here are a few steps on how to break in your new air compressor:
- Before you start using your new air compressor, make sure that you read the manual as this will help you understand how it works and what safety precautions you need to take.
- Once you have read the manual, it's time to start breaking in your new air compressor and begin by filling the tank with oil. And make sure to turn the switch from auto/off to off and when you want to start the air compressor then turn the switch to auto mode.
- Open the drain valve so that there is no pressure build-up during this process.
- Connect it to an electrical outlet and turn on the machine and let it run for about 15 to 30 minutes. (when connecting to an outlet be sure to check the air compressor voltage requirement otherwise it can damage the compressor.)
- Now turn the unit off and let it cool for some time.
- After that, close the drain valve and allow the air compressor to build up the pressure. When this process is done you are good to go.
Frequently Asked Questions (FAQ):
How To Break In A Mcgraw Air Compressor?
To break in a Mcgraw air compressor first you need to turn the power switch off and also unplug the power cord. Now open the regulator as well as the drain valve and then plug in the power cord and turn the power switch on. Let the compressor run for about 15 minutes allowing the air to leave freely from the drain valve and when this is done then turn the power switch off. Now close the drain valve as well as unplug the power cord and that's it you are done.
How To Break In Dewalt Air Compressor?
For this procedure first, you need to make sure the Auto/Off switch is Off and check the oil level in the pump and also make sure all the wiring is connected properly as well as is not obstructed in any way. Now, open the drain valve to allow the air to leave and to prevent any pressure build-up in the air tank during this process, and turn the Auto/Off switch to auto to start the air compressor.
Run the unit for about 30 minutes and after it is done turn the switch to the Off position and close the drain valve. Now again turn the Auto/Off switch to the auto so that the air receiver will fill to cut-out pressure and the motor will stop and you are done with the process.
How To Break In A Porter Cable Air Compressor?
Same procedure here first of all make sure the pressure switch lever is in the OFF position and also make sure the wires are secure at all terminal connections. Open the drain valve to prevent pressure build-up in the tank and also for air to leave. Now turn the pressure switch lever to On/Auto to start the air compressor and run the unit for about 30 minutes and make sure the drain valve is open and there is small air pressure build-up in the tank.
After the required time is passed then again turn the pressure switch lever to the OFF position, check the oil, and add if necessary. Again close the drain valve and turn the pressure switch lever to On/Auto then the air receiver will fill to cut-out pressure and the motor will stop and now you are ready to use the air compressor.
Conclusion:
Following the above steps will ensure that your air compressor will have a long life. By breaking in your new air compressor properly, you can avoid costly repairs or downtime, and you will also extend the life of your air compressor and get the most out of your investment. I hope that this guide was helpful to you and if it was then kindly share it with other people and have a great day.
Related Post: